20130209_161714.jpg (95.3 KiB) Viewed 22 times
Ok so I have done my due dilligence by reading some of the trouble shooting guides online. I bought my mod chip for my Saturn from Racket boy and never have done soldering before. I bought the unit off Ebay from someone here in the US had never been modded before, so I ordered the chip with the red wire (power) and blue wire (Signal). Because my power board had a what seemed to be a heat sink around the power area to solder I soldered the red wire to the right pin but underneath the board, assume that is right? Anyway I was able to properly install the ribbon cable to the chip and i think the chip is in right. I soldered the blue signal wire to Pin 14 as instructed because it IS a japanese model and the A+B wire trick wont work on it. So when everything was powered on, the system boots up to the time set screen which I bypass (needs a new battery) and the disc in the drive spins..now I also have a US black Saturn when I put a disc in there it seems to spin up much faster, so as the troubleshooting guide said the disc spins, I am not sure as to what level it should be spinning but it spins...the cubes are green in the menu and detects it as an audio disc HOWEVER when i try to play the game disc which is a CD-R burned via ImgBurn at 5x it just is all static and thinks its a music disc. I then put in a US Music CD-R and same thing static then a US Store Bought music disc same thing static. I then put a US region Saturn game Original in it for Shits and Giggles and it again thought it was a audio CD. So I then put all of those discs in the US Saturn unmodded and all were detected as what they should be. So I am not sure if my chip is seated right? Seems to be nice and snug inside and as close to the white harness on the mother board as possible. So what have i done wrong? the space to solder the blue wire is quite tiny but i tinned the copper wire on the chip and then added a tiny bit of solder JUST enough to adhere to that contact point. Tough to see in pics though where it should be connected to...but i did my best. Any thoughts??
Some additional notes:
Sat Feb 09, 2013 5:37 pm
so I saw a few other close ups of course still cleaner than my work and i saw the actual wire soldered to the chip and not to the board per se...so again I melted it removed the joing from where I put it and resoldered it to #14 on the chip but still same symptoms. Could my drive not be spinning up fast enough? I saw a you tube video saying something about the pentiometer not spinning the disc of fast enough and it only reads audio cds...
Ok so I have done my due dilligence by reading some of the trouble shooting guides online. I bought my mod chip for my Saturn from Racket boy and never have done soldering before. I bought the unit off Ebay from someone here in the US had never been modded before, so I ordered the chip with the red wire (power) and blue wire (Signal). Because my power board had a what seemed to be a heat sink around the power area to solder I soldered the red wire to the right pin but underneath the board, assume that is right? Anyway I was able to properly install the ribbon cable to the chip and i think the chip is in right. I soldered the blue signal wire to Pin 14 as instructed because it IS a japanese model and the A+B wire trick wont work on it. So when everything was powered on, the system boots up to the time set screen which I bypass (needs a new battery) and the disc in the drive spins..now I also have a US black Saturn when I put a disc in there it seems to spin up much faster, so as the troubleshooting guide said the disc spins, I am not sure as to what level it should be spinning but it spins...the cubes are green in the menu and detects it as an audio disc HOWEVER when i try to play the game disc which is a CD-R burned via ImgBurn at 5x it just is all static and thinks its a music disc. I then put in a US Music CD-R and same thing static then a US Store Bought music disc same thing static. I then put a US region Saturn game Original in it for Shits and Giggles and it again thought it was a audio CD. So I then put all of those discs in the US Saturn unmodded and all were detected as what they should be. So I am not sure if my chip is seated right? Seems to be nice and snug inside and as close to the white harness on the mother board as possible. So what have i done wrong? the space to solder the blue wire is quite tiny but i tinned the copper wire on the chip and then added a tiny bit of solder JUST enough to adhere to that contact point. Tough to see in pics though where it should be connected to...but i did my best. Any thoughts??
Some additional notes:
Sat Feb 09, 2013 5:37 pm
so I saw a few other close ups of course still cleaner than my work and i saw the actual wire soldered to the chip and not to the board per se...so again I melted it removed the joing from where I put it and resoldered it to #14 on the chip but still same symptoms. Could my drive not be spinning up fast enough? I saw a you tube video saying something about the pentiometer not spinning the disc of fast enough and it only reads audio cds...